The electronic system of ignition provides higher energy of sparking in comparison with usual contact system of ignition. Therefore be careful to touch wires and blocks of system of ignition.

Fig. 1.122. Arrangement of the block of fuses

The block of fuses is located under a cover to the right of a steering column (fig. 1.122).

Information on purpose of safety locks is given in inside of a cover (about the protected chains).

To replace the fused safety lock, open a cover and take a safety lock from a nest.

Fig. 1.123. Safety lock

The faulty safety lock can be distinguished visually on the fused wire (fig. 1.123). The new safety lock should be established instead of fused only after the cause of defect is defined and removed. Color of a safety lock depending on rated current: 10 A – red; 20 A – yellow; 30 A – green. It is allowed to use only standard electric safety locks calculated at a certain size of rated current. The size of rated current is specified on the case of each safety lock. In the block of safety locks there are spare safety locks of various face value.

1. An electronic control unit the engine, the control unit of automatic transmission – 10 A.

2. The fuel pump, an immobilizer – 26 A.

3. Lamps of indexes of turn, stoplights, electric drives of external rear-view mirrors – 20 A.

4. A windshield screen wiper, the windscreen washer pump electric motor – 30 A.

5. The radiator temperature relay – 30 A.

6. ABS, the conditioner of air, the relay of shutdown of the compressor – 20 A.

7. Power windows – 30 A.

8. The audio system – 10 A.

9. Electric heaters of back glass and external rear-view mirrors – 20 A.

10. The radiator fan electric motor relay (high speed) – 30 A.

11. Lighting, back dimensional lamps – 10 A.

12. Fuel nozzles – 10 A.

13. The lighter, a melodious sound signal – 20 A.

14. A combination of devices – 10 A.

15. The indicator of the alarm system, a plafond of illumination of salon, a plafond of local lighting, a plafond of illumination of a luggage carrier, the audio system – 20 A.

16. A safety cushion – 20 A.

17. ABS (a power supply from the battery), an immobilizer block power-supply circuit – 10 A.

18. A sound signal, the central electric lock, the automatic switch (luggage carrier) – 30 A.

The main unit of the relay is installed in a motor compartment on a mudguard of a forward wheel near the rechargeable battery.

1. Relay of regulation of speed of a screen wiper.

2. Relay of turning on of the selector of transmission in situation "N" or "P".

3. Radiator fan electric motor relay (high speed).

4. Relay of fog lights.

5. Stripper of safety locks.

6. Relay of the electric motor of the supercharger.

7. It is not used.

8. Relay of a sound signal.

9. It is not used.

10. It is not used.

11. Air conditioner compressor relay.

12. Radiator fan electric motor relay (low speed).

13-1. A safety lock of fog lights – 20 A.

13-2. A safety lock of a lamp of driving beam (left headlight) – 10 A.

13-3. A safety lock of a lamp of passing beam (left headlight) – 10 A.

13-4. A safety lock of the relay of the electric motor of the supercharger – 30 A.

13-5. A safety lock of a lamp of driving beam (right headlight) – 10 A.

13-6. A safety lock of a lamp of passing beam (right headlight) – 10 A.

1. The stoplight relay in a back spoylere*.

2. Relay of the fuel pump.

3. Relay of management of lighting.

4. Relay of electric heaters of back glass and external rear-view mirrors.

The relay of the central blocking of door locks is located above or behind an electronic control unit the engine.

Blocks of the melodious warning signal and the relay breaker are located on the right in the main unit of safety locks.

Lighting devices	Power and quantity of lamps
Forward headlights (passing beam) - the Halogen lamp	55 W x 2
Forward headlights (driving beam) - the Halogen lamp	55 W x 2
Forward dimensional lamps	5 W x 2
Forward indexes of turn	21 W x 2
Forward fog lights	55 W x 2
Side indexes of turn	5 W x 2
Central top stoplight	27 W x 2
Back indexes of turn	21 W x 2
Stoplights and back dimensional lamps	21\5 W h2
Indexes of turn (trunk lid)	21 W x 2
Dimensional lamps or stoplights with dimensional lamps (trunk lid)	5 W or 21\5 W x 2
Fog lamps (trunk lid)	21 W x 2
Backing lamps	21 W x 2
Lamps of illumination of registration plate	5 W x 2
Plafond of illumination of salon	10 W x 1
Plafonds of local lighting	10 W x 2
Plafond of illumination of a luggage carrier	10 W x 1
Plafond of illumination of a ware box	10 W x 1

Do not touch with hands a glass flask of a halogen lamp. Fatty traces from fingers form rather dense film which reduces lamp light brightness when heating a flask. At casual pollution of a flask wipe it with a piece of any lint-free fabric moistened in ethyl alcohol or white spirit.

       PREVENTION

Adjustment of the direction of light bunches of headlights is operation, very responsible from the point of view of traffic safety. Therefore adjustment of headlights should be carried out only at the service stations having the special equipment and qualified personnel.

1. Open a cowl and establish the supporting rack.

Fig. 1.124. An arrangement of a plastic cover in a back part of a headlight

2. Turn a plastic cover counterclockwise and remove its (fig. 1.124).

Fig. 1.125. Arrangement of the electric socket of a lamp of a headlight

3, Disconnect the electric socket of conducting from the boss of a lamp (fig. 1.125).

Fig. 1.126. Arrangement of a spring clamp of a lamp of a headlight (1)

4. Remove a spring clamp and take out a lamp (fig. 1.126).

Fig. 1.127. Replacement of a lamp of a headlight

5. Replace a faulty lamp on new (fig. 1.127).

6. Establish a new lamp into place in the return sequence.

7. Establish into place and fix a plastic cover, having turned it clockwise.

1. Open a cowl and establish the supporting rack.

2. Turn a plastic cover counterclockwise and remove it.

Fig. 1.128. Removal of a lamp of a forward dimensional lamp

3. Take out a cartridge with a lamp of a dimensional lamp which is located near a lamp of a headlight (fig. 1.128).

4. Take out a lamp from the boss (to pull a lamp without turn).

5. Replace a faulty lamp with new.

6. Establish a new lamp in a lamp in the return sequence.

1. Open a cowl and establish the supporting rack.

Fig. 1.129. Arrangement of a plastic cover of a headlight of passing beam

2. Turn a plastic cover counterclockwise and remove its (fig. 1.129).

Fig. 1.130. Arrangement of the electric socket of a lamp of a headlight of passing beam

3. Disconnect the electric socket of conducting from the boss of a lamp (fig. 1.130).

Fig. 1.131. Arrangement of a spring clamp of a lamp of a headlight of passing beam (1)

4. Remove a spring clamp and take out a lamp (fig. 1.131).

Fig. 1.132. Replacement of a lamp of a headlight of passing beam

5. Replace a faulty lamp on new (fig. 1.132).

6. Establish a new lamp into place in the return sequence.

7. Establish into place and fix a plastic cover, having turned it clockwise.

1. Open a cowl and establish the supporting rack.

2. Turn a cartridge of a lamp counterclockwise and take out it from the headlight case.

Fig. 1.133. Replacement of a lamp of the forward index of turn

3. Press a lamp partially to drown it in the boss, turn counterclockwise and take out a lamp from a cartridge (fig. 1.133).

4. Insert a new lamp into a cartridge and turn it clockwise, having at the same time pressed a lamp.

Fig. 1.134. Installation of a lamp of the forward index of turn

5. Insert into the headlight case a cartridge with a lamp and turn it clockwise (fig. 1.134).

1. Turn a plastic cover counterclockwise and remove it.

Fig. 1.135. Arrangement of a spring clamp of a forward fog light

2. Remove a spring clamp and take out a lamp (fig. 1.135).

3. Disconnect the electric socket.

4. Replace a faulty lamp new.

5. Establish a new lamp into place in the return sequence.

1. Remove the lens of a lamp, having turned it counterclockwise.

Fig. 1.136. Removal of a lamp of the side index of turn

2. Take out a lamp (fig. 1.136).

Fig. 1.137. Installation of a lamp of the side index of turn

3. Replace a faulty lamp new (fig. 1.137).

4. Establish into place the lens and fix him, having turned clockwise.

1. Open a trunk lid and disconnect a protective cover.

Fig. 1.138. An arrangement of a clamp of fastening of the panel with lamps of the back combined lamp

2. Press the top clamp and remove the panel with lamps, having pulled it (fig. 1.138) up.

Fig. 1.139. An arrangement of lamps on the panel of the back combined lamp

3. Press a lamp and turn it counterclockwise to take out from a cartridge (fig. 1.139).

4. Replace a faulty lamp with new. Insert a lamp into a cartridge and turn it clockwise with simultaneous pressing.

5. Install the panel with a new lamp in the holder on the lamp case, having advanced it against the stop down. Fix the panel by the top clamp.

1. Dig out a trunk lid.

Fig. 1.140. An arrangement of the electric socket of conducting on a trunk lid

2. Disconnect the electric socket of conducting (fig. 1.140).

3. Turn counterclockwise a cartridge with a lamp and remove it.

4. Press a lamp and at the same time turn it counterclockwise to take out from the boss.

5. Replace a lamp with new.

6. Establish a new lamp into place in the return sequence.

7. Arrangement of lamps.

From above on inside – a lamp of a fog lamp.

From above on the outer side – a lamp of a dimensional lamp or a lamp of a stoplight and a dimensional lamp.

From below – a lamp of the index of turn.

Fig. 1.141. Removal of a lamp from a trunk lid

1. Unscrew two screws and remove a lamp (fig. 1.141).

Fig. 1.142. Removal of the boss with a lamp from a trunk lid lamp

2. Turn a cartridge with a lamp counterclockwise and remove its (fig. 1.142).

3. Press a lamp and at the same time turn it counterclockwise to take out from the boss.

4. Insert a new lamp into a cartridge and fix it by turn clockwise with simultaneous pressing.

5. Install a cartridge with a lamp in the case of a lamp and fix a cartridge, having turned it clockwise.

6. Screw into place two screws.

1. Unscrew two fixing screws and remove the lamp case.

2. Take out a cartridge with a lamp from the lamp case, having turned it counterclockwise.

3. Take out a lamp from the boss.

4. Insert a new lamp into a cartridge

5. Install a cartridge with a lamp in the case of a lamp and turn a cartridge clockwise.

6. Wrap two fixing screws.

Fig. 1.143. Use of the screw-driver for removal of a plafond of illumination of salon

1. By means of the screw-driver take out a plafond from a nest (fig. 1.143).

2. Slightly press a lamp in the direction of a spring clamp and take out a lamp.

3. Insert a new lamp.

Fig. 1.144. Use of the screw-driver for removal of a plafond of local lighting

1. By means of the screw-driver take out a plafond from a nest (fig. 1.144).

2. Slightly press a spring clamp and take out a lamp.

3. Replace a lamp and establish a plafond into place.

Fig. 1.145. Places of designation of polarity of plugs of a plafond of illumination of a luggage carrier

Polarity of the attached electric wires "+" or "-" is designated on plugs of a plafond (fig. 1.145). When replacing a lamp be attentive not to mix polarity of wires. Polarity "+": color of a wire – red, wire section – 0,5 mm2. Polarity "-": color of a wire – gray, wire section – 0,5 mm2.